Toyota Tacoma Rear DuroBumps
Toyota Tacoma Rear DuroBumps Toyota Tacoma Rear DuroBumps Toyota Tacoma Rear DuroBumps Toyota Tacoma Rear DuroBumps Toyota Tacoma Rear DuroBumps Toyota Tacoma Rear DuroBumps Toyota Tacoma Rear DuroBumps Toyota Tacoma Rear DuroBumps Toyota Tacoma Rear DuroBumps Toyota Tacoma Rear DuroBumps
$138.00

***Any shipping charges over $10 will be refunded the difference upon fulfillment of your order***

The 1st and only dual durometer rubber bump stops created application specific for the Toyota Tacoma. Proudly made in the USA. We don’t create just one universal size bump stop and sell spacers to accommodate your specific lift, like the competitors. In an industry first, we offer 3 different size rubber DuroBumps to accommodate anything from stock trucks with our 3.5″ version, a 4.25″ version for lifts of 2″+ (which is the most commonly used) and a 5.25″ version for custom applications and all you wild builders with custom shock mounts looking for something a bit taller. With proper size selection, DuroBumps are designed to help eliminate or greatly reduce over-arching your rear leaf springs.

Tacoma rear DuroBumps can be mounted to just about any rear Leaf Pack. Our standard mount that is included with any rear DuroBumps set, is intended to be used with OEM square shaped U Bolts. Our mounting plate is fastened underneath the saddle of the U Bolts.

  • 3.5″ version Durobumps: Stock to mild lifts up to 1.5″ (Factory length shocks or +1″, Factory shock mounting location) Diameter: 3.75″(95mm)  Height: 3.5″(89mm)

  • 4.25″ version Durobumps: Tacomas with lifts of 2″+.(Factory length shocks or +1″, Factory shock mounting location) Diameter: 3.75″(95mm)  Height: 4.25″(108mm)

  • 5.25″ version Durobumps: Custom applications ONLY such as; shock mount relocation, 12″+ shocks, custom suspension builds, etc. Diameter: 3.75″(95mm)  Height: 5.25″(133mm)

U-Bolt Flip Kit (Upgrade)

Upgrade your rear OEM Thin U-bolts and mounting plate by purchasing our new 3/8″ Steel Plate U-Bolt Flip Kit. Our 3/8″ steel plates are extra heavy duty with bent ends and tough powder coat finish to prevent corrosion. Flip kits include Four (4) heavy duty OME 9/16″ x 3.25″ x 7.75″ Black U-Bolts.

With DuroBumps, Toyota Tacoma Rear Bump Stops combined with our very own U-Bolt Flip Kit you will have the ultimate combination in performance, strength and style.

(Please Note: Customer is responsible to verify proper length U-bolts selected)

(1st Gen Tacomas: It will be necessary to purchase and weld an aftermarket shock tab to the axle tube as the factory shock mount is eliminated when replacing the OEM leaf spring perch)

What’s Included in the Package:

  • 2pcs. Tacoma rear DuroBumps bump stops.

  • Mounting plate: (Standard mounting plate included with Tacoma rear Durobumps)

  1.   Two pcs (2) Standard Mounting Plate, for use with OEM square shaped U-bolts

  2.   Upgrade Option: U-bolt flip kit w/ OME Black U-bolts 9/16″ x 3.25″ 7.75″ long.

  • 4pcs. JIS 10.9 corrosion-resistant metric mounting hardware.

  • Install Instructions.

Please Note:

  • Customer responsible for choosing proper size bump stop for intended application.

  • For off-road use only. By installing these after market bump stops on your vehicle you assume all risk and liability. Seller will not be held liable for any damages or loss associated with the installation or use of this product for any reason.

Durobumps are not a replacement for air or hydro bump stops. Durobumps are for Trail guys & gals, Rock Crawlers and Overlanders. DuroBumps may make you feel like Ivan “Ironman” Stewart on the trail BUT, proper suspension setup and roll cage at the minimum are required to safely and responsibly drive at high speeds off road. Our products are not recommended for High Speed Pre-Runner applications OR Towing. Durobumps are the absolute best Bump Stops available on the market and we are sure you will agree!!

ATTENTION STATE OF CALIFORNIA CONSUMERS. WARNING: Cancer or Reproductive Harm – www.p65warnings.ca.gov